Mac Forum / Applications / Virtual PC / April 2007

I have Vista Ultimate x86 on a nForce 590 AMD SLI platform. After installing
and running Virtual PC 2007, during boot up, it will cause network driver
malfunctions (according to Vista diagnosis). Basically after restart, my
network is down. Sometimes I can reboot and get it back, ...

I have attempted to use Windows XP on Virtual PC 7.0.2 to program a
Garmin GPS datacard using a Jeppesen Skybound USB card programming
device. I have set the Virual PC Preferences to recognize an "unknown
USB device." Everything about the software (Jeppesen) and hardware

Hi Folks, I'm running a 20"  iMac, 1.25 PowerPC G4, OS X 10.4.9, & 1.5
Gig RAM.  I had VPC 6.1 installed and running with Windows XP Pro.  I
just installed VPC 7.01 Upgrade.  The installation seemed to go just
fine BUT, when Windows opens, my cursor is confined / restricted to

I was using "Virtual PC w/ Windows XP Professional" on my iMac G4 and
recently purchased an intel iMac.  I'd like to use boot-camp to run
windows, but can't figure out if I can somehow use the Windows XP
Professional "included" with my virtual PC program.   There doesn't

i have thgis useless waste of a program that cost $200 and i was
wondering if i could somehow get the windows app from it to be used by
boot camp or parallels
in  mty intel imac?

My VirtualPC 7/Windows XP Pro has been running without problems for
about a year on an iMac (PowerPC, OSX 10.4.8). The other day the XP
started updating itself and then went into restart. The restart failed
flashing an error message (bad image checksum) and going back to

I would like to ask if anyone can please help me with the following
problem.
I installed Microsoft Virtual PC 2007 on a windows XP host machine,
and I installed windows XP as a virtual guest OS.

I've been running VPC fine for a 4+years.  I've had VPC 7 on this
particular machine (Powerbook G4 17") for over a year without
problems.  I had VIrtual PC open with a few applications running and
moved over to the Mac side to work on something different.  I left it

I have osx 10.4.3 installed on a Powerbook G4 1GHz.  Also installed is
VPC 7.0.2 with WinXP Pro.  I can not Get Activesync to reconize my Dell
Axim 51v with WM5.  The Axim can only have WM5 installed so rolling
back to Activesync 3.8 is not an option.  I did have an older Ipaq that

I am running OS X 10.4 (tiger) on a MacBook Pro and Vrtual PC 7 will
not work with my OS. I believe that all I need to do is to download
the 7.0.2 update ofr Virtual PC but firefox nor safari will open the
page once i click download. I get a cannot find server error for each.

I am running a G4 800 Mac. The system is 10.4.8.
I bought Virtual PC 7 a couple of years ago and tried to install it
today. I have three disks (2 blue; 1 gray). I got to the point of
writing in the product key. I can't get it to go on to the next step

I have a network problem with virtualpc
My mac is connected to internet with a dsl router wich is always on.
the router IP address is 192.168.0.1
the mac IP adress is 192.168.0.2

I have been using VPC7 since it came out. I have an XP and 2000
Virtual machine on a G5. Here is the problem: Win 2000 machine will
not let me use mouse to select start menu or for that matter anything
on the desktop. I just have the ability to draw a marquee. My XP

I installed VPC 7.0 w/Win XP Pro then upgraded to 7.02
during install of disks it says "installing windows"  after finished
a black screen with Windows XP Professional on top of screen (not in
screen) pops up .  At this point I am supposed to configure windows

I am one of the very few mac users in my company.  The company's e-
mail architecture is set up around outlook.  Is one okay using
Entourage or does one need to run Outlook via Virtual PC 7?  Any
thoughts?